MINI2

Hoganscrogan · Mar 5th, 2002, 11:40 AM

Sounds great and only costs £89 - however instructions are pretty poor!

Bits I got stuck on are explained below. YOU WILL NEED TO USE THE PIPERCROSS INSTRUCTIONS IN CONJUNCTION WITH THESE TIPS

TAKING BITS OFF

Once main airbox has been removed (pretty easy) you need to take off the flexipipe (C/B) from the airscoop (A) Not so easy.

Undo the 3 clips (A) and slide out scoop, this makes the flexipipe (C) alot easier to get off. Ease off flexi pipe being carful not to crush. Clip scoop back on after pipe removal.

FITTING BITS

What 's not clear is where some of the brakets go.

First bolt (D) to the the big black bracket (E) using bolt and washer. Fit rubber washer (F shown yellow) around the outside of the intake pipe. Open up the jubilee clip (G) and thread it through the small silver mounting (D). Now fasten (G) back together and then place loosly around the air intake pipe and washer(F). Loosly bolt right hand end of (E) to the chassis member using supplied bolt and antishake washer.
Slip cone filer in end of air intake pipe and tighten
jubilee clip (G) until a seal is obtained - tight but not too tight! Once this is fitted OK tighten up the chassis mounting bolt on right of bracket (E).

Check you've not left any tools on the engine, no wires/pipes are rubbing on your new bits then close bonnet and drive off.

You will not be disapointed!!!!

FOR MORE IMAGES
http://homepage.mac.com/hoganscrogan/

Paul · Mar 5th, 2002, 12:08 PM

Excellent, thank you.

ant · Mar 5th, 2002, 12:17 PM

Impressive stuff!

Noticed any difference in performance? Obviously the induction noise alone is worth it though

Hoganscrogan · Mar 5th, 2002, 01:27 PM

A bit more urge at the top maybe. When you look at the standard box and filter the engine must breathe alot easier.

Mar 5th, 2002, 11:40 AM	#1
Hoganscrogan MINI2 Newbie Join Date: Sep 2001 Location: Leeds Local Time: 06:34 PM Posts: 23 Offline	Pipercross Induction Kit Install Tips Sounds great and only costs £89 - however instructions are pretty poor! Bits I got stuck on are explained below. YOU WILL NEED TO USE THE PIPERCROSS INSTRUCTIONS IN CONJUNCTION WITH THESE TIPS TAKING BITS OFF Once main airbox has been removed (pretty easy) you need to take off the flexipipe (C/B) from the airscoop (A) Not so easy. Undo the 3 clips (A) and slide out scoop, this makes the flexipipe (C) alot easier to get off. Ease off flexi pipe being carful not to crush. Clip scoop back on after pipe removal. FITTING BITS What 's not clear is where some of the brakets go. First bolt (D) to the the big black bracket (E) using bolt and washer. Fit rubber washer (F shown yellow) around the outside of the intake pipe. Open up the jubilee clip (G) and thread it through the small silver mounting (D). Now fasten (G) back together and then place loosly around the air intake pipe and washer(F). Loosly bolt right hand end of (E) to the chassis member using supplied bolt and antishake washer. Slip cone filer in end of air intake pipe and tighten jubilee clip (G) until a seal is obtained - tight but not too tight! Once this is fitted OK tighten up the chassis mounting bolt on right of bracket (E). Check you've not left any tools on the engine, no wires/pipes are rubbing on your new bits then close bonnet and drive off. You will not be disapointed!!!! FOR MORE IMAGES http://homepage.mac.com/hoganscrogan/ Last edited by Hoganscrogan : Mar 5th, 2002 at 11:55 AM.

Mar 5th, 2002, 12:08 PM	#2 (permalink)
Paul Trained Monkey My Classifieds Join Date: Jan 2001 Location: Bedfordshire Local Time: 06:34 PM Posts: 41,218 Online	Excellent, thank you. There aint no party like my nana's tea party

Mar 5th, 2002, 12:17 PM	#3 (permalink)
ant MINI2 Regular Join Date: Dec 2001 Location: Elland (nr. Halifax) Local Time: 06:34 PM Posts: 195 Offline	Impressive stuff! Noticed any difference in performance? Obviously the induction noise alone is worth it though Indie Blue/White Cooper ordered - Expecting Late March... hang on - make that mid March. No, wait - it's here!!!!!!!!!! Woo Hoo!!!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Rate This Thread
Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
One with pipercross induction kit	minioneandrew	Engine & Drivetrain Tuning	3	Nov 27th, 2006 09:14 PM
Pipercross induction kit	DaMiniFreak	Engine & Drivetrain Tuning	2	Aug 9th, 2006 07:01 PM
Anyone got a pipercross induction Kit on there 'S'?	RIGGERS	Engine & Drivetrain Tuning	6	Dec 11th, 2003 05:25 PM
Pipercross Induction Kit - HELP!	chrislemon	Engine & Drivetrain Tuning	8	May 27th, 2003 02:40 PM
Pipercross Induction kit for S	MJS	Engine & Drivetrain Tuning	6	Mar 20th, 2003 08:37 PM

MINI2

Fuel for your MINI obsession

From air-filters to exhausts and all in between, discuss them here

Today
Sponsors	Sponsored Links Registered members do not see Google Ads posts, they can also post messages, pictures, and classified adverts. Register your free account today and become a member of MINI2 - MINI Forum

Mar 5th, 2002, 01:27 PM	#4 (permalink)
Hoganscrogan MINI2 Newbie Join Date: Sep 2001 Location: Leeds Local Time: 06:34 PM Posts: 23 Offline	A bit more urge at the top maybe. When you look at the standard box and filter the engine must breathe alot easier.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)