Mini2.com Forum Header Mini2.com Forum Header
» Premium
» Wheel & Tire Center

» Sponsors
» Sponsors
Go Back   MINI2 - MINI Forum > MINI Technical Forums > MINI Engine & Drivetrain Tuning > First Generation MINI Tuning

First Generation MINI Tuning Tuning the first generation MINI 2001 - 2006

Please Visit our Site Sponsors

MINI2.com is the largest MINI Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Rate Thread
  #1 (permalink)  
Old Mar 16th, 2007, 02:04 PM
Alex5
Offline
MINI2 Regular
 
Join Date: Jan 2007
Location: Buying Mini bits
Posts: 82
Local Time: 10:20 PM
England Male
Samco / Alta silicone induction hoses

Hi

I have the Madness CAI and am keen to replace my stock inlet hose with either the Samco or Alta silicone offering. I would just like to gauge opinions on these before making a purchase.

- I think the Alta is more easily available, but seem to recall others having problems with it being too loose a fit to throttle body / intake.

- Samco have a good reputation but I have not seem this hose mentioned on here before. If it is a better fit than the Alta I'd prefer it, but they seem to have long supply waits (4-6 weeks if not in stock).

Your thoughts and comments appreciated

Alex
Reply With Quote
Sponsored Links
Advertisement
 

  #2 (permalink)  
Old Mar 16th, 2007, 02:36 PM
HObzy's Avatar
HObzy
Offline
MINI2 Master
 
Join Date: Oct 2003
Location: Stressville
Posts: 1,029
Local Time: 11:20 PM
United Kingdom View HObzy's Indi Blue & Black 1st Gen MINI Cooper S Profile
I have the Samco hoses. Good fit diameter wise but needed cutting to length. Fiddly job but not taxing. Being hand wound to a pattern means the wait is long if they haven't recently done a batch, but there are quite a few tuners/suppliers out there offering them so you should be ok to get them.

Worst bit is getting the old clips off - easier if you've got the special tool.
Reply With Quote
  #3 (permalink)  
Old Mar 16th, 2007, 02:53 PM
Richard Crofts's Avatar
Richard Crofts
Offline
THE STICK
 
Join Date: Feb 2003
Location: Worcestershire WR15
Posts: 3,905
Local Time: 10:20 PM
United Kingdom Male View Richard Crofts's Dark Silver & Black 1st Gen MINI Cooper S Profile
Its called a thin blade screw driver and a replacement pack of jubiliee clips Don't try to re-use the stock clips they are crap anyhow

I have the Alta intake on my S and the throttle body fit could be better but if you line things up right and put the clip on right then its not a problem. The samco one might be better but I have no experience (the alta one is designed to fit the Alta intake to the throttlebody not sure if its a direct sized replacment for the stock pipe?

Speak to Lohen as they sell both I think

This is the most unprofessional bit of site management I have seen since I was banned from a certain other site...at least they had the excuse that they were enthusiasts who had strong views and not professionals paid to keep thier cool!
Reply With Quote
  #4 (permalink)  
Old Mar 16th, 2007, 04:15 PM
HObzy's Avatar
HObzy
Offline
MINI2 Master
 
Join Date: Oct 2003
Location: Stressville
Posts: 1,029
Local Time: 11:20 PM
United Kingdom View HObzy's Indi Blue & Black 1st Gen MINI Cooper S Profile
Didn't say it was impossible thats what i used for that pipe, but have to say, when i did the others and used the (very cheap) tool, it saved a lot of time and bruised knuckles and cursing Especially as the stock TB one is usually underneath the pipe...
Reply With Quote
  #5 (permalink)  
Old Mar 16th, 2007, 04:18 PM
Alex5
Offline
MINI2 Regular
 
Join Date: Jan 2007
Location: Buying Mini bits
Posts: 82
Local Time: 10:20 PM
England Male
Oh yeah tell me about the stock 'clips'... I actually thought they had come undone when I first saw them, but no, they're just useless... presently a cable tie is doing a better job holding stock hose to CAI inlet.

Didn't realise Lohen stocked them both, cheers for the tip.
Reply With Quote
Reply

Tags: , ,



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Samco Silicone Hose Kit WHITEY_ First Generation MINI Tuning 8 Aug 29th, 2007 11:51 AM
R56 Silicone Hoses marx87 Second Generation MINI Tuning 2 Jun 6th, 2007 12:25 PM
Samco hoses cooper s-exy Second Generation MINI Tuning 0 Mar 18th, 2007 05:22 PM
NEW! Samco Coolant hose kits and Induction hoses Lohen First Generation MINI Tuning 4 Sep 20th, 2006 09:58 AM

Powered by vBadvanced CMPS v3.1.0

All times are GMT. The time now is 10:20 PM.


Powered by vBulletin® Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.2.0